Additive Manufacturing Prototype for Improved Performance of Mass Timber Using Forest Residues

/
/
/
Additive Manufacturing Prototype for Improved Performance of Mass Timber Using Forest Residues
Prototype Design and Additive Manufacturing for Improved Acoustic and Thermal Performance of Mass Timber Components Using Forest Residues

Research Team:
Pavan Akula, Lead PI – OSU, School of Civil and Construction Engineering
Dylan Wood – UO, School of Architecture & Environment
Islam Hafez – OSU, Department of Wood Science and Engineering
Devin Roach – OSU, School of Mechanical, Industrial, and Manufacturing Engineering
Yakun Zhang – OSU, Department of Crop & Soil Science

Vaibhav Vinod Ingle – PhD, OSU, School of Civil and Construction Engineering

Project Duration:
2025-2026
 
Research Advisory Group:

Global Hemp Innovation Center, OSU
TallWood Design Institute

Facilities:
Graf Hall
A.A. “Red” Emmerson Advanced Wood Products Lab
Civil and Construction Engineering Materials Laboratory
Richardson Hall

Introduction

Cross-laminated timber is a fast-growing, low-carbon structural system, but the standardized flat panel that makes CLT efficient to manufacture is also what limits it: in wall and floor assemblies, thermal, acoustic, and fire requirements are met by adding gypsum, insulation, or a concrete topping, which adds mass, trades, and embodied carbon. Earth-based topping layers have recently been proposed as an alternative route to these functions in timber floor assemblies (Trummer et al., 2022). The premise of this project is a division of labor: the timber carries the structural load, and a thin printed geomaterial layer carries the envelope functions.

The project combines large-scale additive manufacturing with soil, biochar pyrolyzed from Douglas-fir forest residues, local hemp fiber, and Portland cement at low dosage. Each constituent has a defined role. A clay-size fraction near 30% supplies the yield stress and thixotropic recovery needed for extrusion and buildability, a window identified in the PI’s earlier work on printable clay-rich soils (Gyawali et al., 2024; Lonsford et al., 2025). Biochar contributes a porous, low-density carbon skeleton that lowers effective thermal conductivity while sequestering carbon. Hemp fiber bridges drying shrinkage cracks and stabilizes the printed filament. Cement, capped at 30% by weight of soil, provides strength and moisture resistance without turning the material into a concrete. Using timber and agricultural residues in this way shortens the supply chain, keeps value in rural Oregon, and supports the Oregon Mass Timber Coalition’s goal of scaling mass timber manufacturing at a lower environmental cost.

Research Methods

The work was organized into three tasks.

Task 1 — Materials and Mix Design. Soil with approximately 30% clay-size fraction was combined with biochar produced by pyrolyzing forest residues, Portland cement at up to 30% by weight of soil, and hemp fiber for shrinkage control. Four mixes were compared: a soil–binder baseline, baseline plus biochar, baseline plus hemp fiber, and a combined mix. Water demand, flowability, extrudability, buildability, and open-time behavior were screened through printing trials at Graf Hall.

Task 2 — Engineering and Thermal Characterization. Engineering performance was evaluated on cast specimens through unconfined compressive strength (ASTM D2166), flexural strength on prismatic beams under third-point loading (ASTM D1635), and bulk density, so that strength differences could be separated from density effects. Thermal performance was measured as steady-state thermal conductivity using a heat flow meter apparatus (ASTM C518) at Richardson Hall. Results were benchmarked against target mix properties to guide refinement. Acoustic performance was not part of this phase.

Robotic 3D printing of the soil–biochar–hemp–cement composite onto a CLT panel at the Emmerson Advanced Wood Products Laboratory.

Task 3 — Printing and Design Development. Candidate geometries were printed on the robotic platform at the Emmerson Lab, and one geometry was selected and printed as a full 4 ft × 8 ft panel. Parametric modeling was used to tune the geometry for consistent layer alignment and efficient load distribution, and print quality was tracked through interlayer bonding, dimensional accuracy, build-height stability, and drying shrinkage.

Key Findings

Mix design and printability. Adding biochar increased water demand relative to the soil–binder baseline and produced a softer, more flowable mix. Hemp fiber also raised water demand but yielded a stiffer mix and visibly reduced shrinkage. The combined mix performed best overall, improving printability, buildability, and shape stability of the deposited filament. Drying shrinkage was not eliminated in any mix; the soil continued to shrink on drying, and this remains the governing fresh-to-hardened state issue for the material.

Engineering performance. The soil–binder baseline reached approximately 11–13% higher unconfined compressive strength than the combined mix. Bulk density of the baseline was about 3% higher, so part of the strength difference is a direct consequence of replacing mineral solids with low-density biochar and fiber rather than a loss of binder efficiency.

Thermal performance. The combined mix reduced thermal conductivity by 29.5% relative to the soil–binder baseline. The improvement held across mixes irrespective of bulk density, which indicates that the gain comes from the internal pore structure of the biochar rather than from bulk density alone. Taken together, roughly a 30% thermal gain for about a 12% strength penalty is a favorable trade for a layer that is not carrying structural load, and it establishes a workable baseline mix for scale-up.

Fresh-state printing trial at Graf Hall used to screen extrudability and buildability of the candidate mixes.
Future Work

Future work will separate the individual contribution of each constituent soil, biochar, cement, and hemp fiber and help develop multifunctional materials ranging from high strength to fire resistance. In the fresh state, the emphasis is on flowability, buildability, and open time. In the hardened state, the goal is to recover compressive and flexural strength while improving fire that is already demonstrated, and to reduce the drying shrinkage inherent to a soil-based mix through fiber dosage and length, binder chemistry, and curing regime. Durability testing will address moisture resistance, and long-term dimensional stability. Acoustic transmission loss, which was not measured in this phase, remains a key next step in validating the multifunctional case for the printed layer, alongside fire performance testing and full-scale evaluation of the integrated CLT-plus-printed-layer assembly.

Publications & Presentations

Findings from this project were presented at the TallWood Design Institute Fall Symposium, and a journal manuscript covering the mix design and thermal–mechanical trade-off is in preparation.

Funding & Acknowledgements

This work, entitled “Prototype Design and Additive manufacturing for improved acoustic and thermal performance of mass timber components using forestry waste product”, was supported by the USDA Agricultural Research Service Award No. 59-0200-5-001 through the TallWood Design Institute. The team thanks the Global Hemp Innovation Center at OSU for guidance on hemp fiber selection and supply, and the Emmerson Advanced Wood Products Laboratory technical staff for support during robotic printing.

References

ASTM International. (2021). Standard test method for steady-state thermal transmission properties by means of the heat flow meter apparatus (ASTM C518-21).

Gyawali, B., Haghnazar, R., Akula, P., Alba, K., & Nasir, V. (2024). A review on 3D printing with clay and sawdust/natural fibers: Printability, rheology, properties, and applications. Results in Engineering, 24, 103024. https://doi.org/10.1016/j.rineng.2024.103024

Lonsford, H., Ray, S., Su Shin, M., & Akula, P. (2025). Optimal geotechnical and mineralogical properties for 3D printing of clay-rich soils. In Geotechnical Frontiers 2025 (pp. 383–393). https://doi.org/10.1061/9780784486009.039

Trummer, J., Schneider, M., Lechner, M., Jarmer, T., Demoulin, T., Landrou, G., Nagler, F., Winter, S., & Dörfler, K. (2022). Digital design and fabrication strategy of a hybrid timber-earth floor slab. IOP Conference Series: Earth and Environmental Science, 1078(1), 012062. https://doi.org/10.1088/1755-1315/1078/1/012062